3
$\begingroup$

I am working on a cathode ray tube (CRT) based off of an original model. Is there a way to make a glass object (the tube) hollow? In reality, the tube is not filled with glass, so the glass shader default does not yield a good result. I have tried extruding the faces of the mesh a tiny bit inwards, but the result is that the mesh is distorted on the inside. I also tried duplicating the mesh, and scaling it down a tiny bit, but then I have to set the IOR of the shader to something really low, like 1.05. Is there a node setup, or just some kind of way to model your object so that you can render it like a thin glass tube? I would need to see the inner glass, though, like on here. enter image description here enter image description here My render.

$\endgroup$
7
  • 3
    $\begingroup$ Solidify modifier?? Also CRT tubes were quite thick on the front and acted quite like a lens. $\endgroup$ – Moog Dec 25 '19 at 12:19
  • $\begingroup$ Yep That sort of worked, but not very well. I'll just use that then. I'm making the first model. Not the ones in TVs $\endgroup$ – Nate_Sycro27 Dec 25 '19 at 12:22
  • 2
    $\begingroup$ What do you mean "sort of worked, but not very well"? Solidify is the exact solution for this problem, how much better can it get? $\endgroup$ – Martynas Žiemys Dec 25 '19 at 12:39
  • $\begingroup$ I was hoping that I would be able to see some of the inner glass, but this works well enough. Thank you! $\endgroup$ – Nate_Sycro27 Dec 25 '19 at 12:51
  • 1
    $\begingroup$ Can you describe, why your are not seeing the "inner" of the glass and how would see it in real life photography? Images demonstrating the difference would help. $\endgroup$ – Leander Dec 25 '19 at 13:16
4
$\begingroup$

Perhaps something like this is closer to what you're looking for?

CRT Render

I think this is pretty close to what you've used, but feel free to check out what I've done here.

Transmission = 1

IOR = 1.05

Roughness = 0.167

$\endgroup$
3
  • $\begingroup$ Thank you this helps. Also is there a way to make only the inside reflective? This would be very helpful. $\endgroup$ – Nate_Sycro27 Dec 25 '19 at 15:44
  • 1
    $\begingroup$ Actually, adding a little bit of metallic shading fixes pretty much all of my shading problem. Thanks! $\endgroup$ – Nate_Sycro27 Dec 25 '19 at 15:49
  • $\begingroup$ No problem and happy holidays! $\endgroup$ – stphnl329 Dec 25 '19 at 15:50
3
$\begingroup$

Use Cycles render with the Principled BSDF Shader with the following settings:

Roughness: 0

Transmission: 1

This will yield results show in attached.Glass Cup

$\endgroup$
2
  • 2
    $\begingroup$ This just gives me the same look as the glass shader. $\endgroup$ – Nate_Sycro27 Dec 25 '19 at 15:42
  • 1
    $\begingroup$ Ahh, it looks nothing like the render you submitted. Considering you 'fixed it' by adding metallic shading, I'm guessing you wanted to see both the inner and outer surfaces. If I remember correctly, the glass for CRTs did have a very thin metallic film/powder on them. $\endgroup$ – Mike Dec 26 '19 at 1:22

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.